ALWA MOULD P
Please select the quantity you need and then select below the number of components you want or need to buy.
Amount needed:
Corresponds to:
Contains:
ALWA MOULD P
ALWA MOULD P is a cold curing casting resin for the production of porous moulds, slabs and blocks for the ceramic industry. It is a porous and high-strength plastic, which is well-suited for high pressure casting applications. ALWA MOULD P can be used in various areas of the tableware and sanitary ceramics, technical ceramics, plastic mould procedure as well as various filtration processes. The high stability and defined porosity of the material allows highly accurate mould surface reproductions. With ALWA MOULD P various geometric moulds for filtration processes of suspensions can be produced. ALWA MOULD P can be used for ceramic slip pressure casting procedures. In this procedure, water is removed by a filtration process of a clay suspension (slip), so that an increasing clay layer is built on the mould wall over time. The moulds, slabs and blocks of ALWA MOULD P are easily machinable (e.g., drilling, milling).
ALWA MOULD P can be flexibly adjusted due
to the customers’ requirements concerning the total porosity and average
pore diameter.
Application: | Air film control technology, Molds for the ceramics industry, Vacuum clamping technology |
---|
Processing
The temperature of the room and pattern should be between 17 and 20 °C, otherwise the pot life changes.
Application example No. 1
Batch quantity < 10 kg | |||
---|---|---|---|
Aim: Average pore diameter from ~ < 10 µ | Resin and water are mixed homogeneously. | The mixture is carefully stirred into the filler at a rotational speed of approx. 700 – 1000 for approx. 90 sec. | After the resin and the filler have been mixed homogeneously, the casting compound has to be poured within 5 min. |
Aim: Average pore diameter from ~ < 20 µ | Resin and water are mixed homogeneously. | The mixture is carefully stirred into the filler at a rotational speed of approx. 550 for approx. 70 sec. | After the resin and the filler have been mixed homogeneously, the casting compound has to be poured within 5 min. |
Application example No. 2
Batch quantity > 10 kg We recommend to stir the complete mixture in a bucket. Afterwards, transfer one half into a second bucket. Mix both mixtures according to the remaining stirring time. | |||
---|---|---|---|
Aim: Average pore diameter from ~ < 10 µ | Water and filler are mixed homogeneously (approx. 60 sec.). | The resin is immediately added to the mixture at a rotational speed of approx. 415 for approx. 90 sec. | After the resin and the filler have been mixed homogeneously, the casting compound has to be poured within 5 min. |
Aim: Average pore diameter from ~ < 20 µ | Water and filler are mixed homogeneously (approx. 60 sec.). | The resin is immediately added to the mixture at a rotational speed of approx. 485 for approx. 70 sec. | After the resin and the filler have been mixed homogeneously, the casting compound has to be poured within 5 min. |
For mixing, we recommend to use exclusively our special mixers with the buckets provided as well as explosion proof mixing devices with the most accurate speed controller. After curing of the mould (approx. 2 ½ – 3 ½ hours after adding the resin), it is demoulded and the casting is put into a heated water bath up to 40 °C for approx. 12 hours. The mould is wrapped in a foil for storage, so that no water can escape. Mould areas that should not be porous are sealed with lacquer. The moulds must not dry out and, therefore, are generally stored in a water bath.
Downloads
Product brochure:
CASTING RESIN FOR THE CERAMIC INDUSTRY ALWA MOUD P
Preparation of the pattern
The surfaces to be treated must be completely clean (free of dust and grease).
a) Build up the pattern on a base plate. Porous patterns (e.g., PU foam) must be smoothed with putty.
b) Absorbent surfaces (e.g., wood, plaster) are sealed with lacquer (do not use acrylic lacquer!).
Calculation of the batch quantity
Calculate the casting volume in litre. In order to make up casting losses, we recommend increasing the batch quantity by approx. 5 %.
Product | Article number | Parts |
---|---|---|
ALWA MOULD P | 2000 | 20 |
Filler | 2720 | 52 |
Water | 28 |
Packages
Product | Unit | Package |
---|---|---|
Resin | 5 | Can |
25 | Hobbock | |
50 | Drum | |
200 | Drum | |
Filler | 10 | Bucket |
50 | Drum |
Characteristic | Unit | Value |
---|---|---|
Processing temperature of the mixture | °C | 15 – 16 |
Glass transition temperature | °C | approx. 100 |
Reaction temperature | °C | < 65 |
Density according to DIN 1306 (filled with water) | kg/l | 1.05 |
Shelf life at 16 °C to 22 °C (do not store below 12 °C) | month | 6 |
Total porosity of the mould | % | 28 – 32 |
Average pore diameter of the mould | µ | 7 – 22 |
We are here for you!
Phone: +49 2562 98157
E-Mail: info@alwa.de
ContactMonday to Thursday
8 am - 5 pm
Friday
8 am - 2 pm